Phone: (07) 5563 1982 | 1300 146 737

Select Page

3 Phase Metal Forging Hydraulic Press Motor & 2 Speed Pump.

14/3.2
AU$2 139.95
In stock
1
Product Details

Metal Forge Hydraulic Press Hammer Electric Motor + Hi Lo Splitter Pump
This is a ready-to-be-wired-up, 3-phase 415-volt 7.5 kW (10 Hp) electric motor,
plus bell housing, shaft couplers & a cast iron hydraulic Hi Lo pump.

If you only have 240 Volt single phase and require a complete DIY Hydraulic Kit
Please click the link below to see the our 240 volt package!

240 Volt DIY Single Phase Hydraulic Metal Forging Kit

This setup will produce approximately 45 Lt/min of flow
Using a hydraulic cylinder with a 5" bore high flow will produce a down speed
of 25 mm/second and an up speed of 30 mm/second
In Low flow, it will produce a down speed of 4 mm per second with
25 tons of force and an up speed of 5 mm per second.
The cycle time as well as the forces generated and will vary depending on
the bore & stroke of the hydraulic ram you are using.

Please contact us with your requirements.
Please note; electric plug cables are not supplied with these units as per Australian law.
There is a wiring diagram under the motors power terminal lid.
An Licenced Electrician is required by law to connect it up.
MOTOR ROTATION is Clockwise when looking at the motor's rear cooling fan

"Joe the Builder" Built this Beauty.

Check Out Paul Pinto's Video On How He Built His Awesome Hydraulic Press For Blacksmithing

A few examples using 5" bore rams
with a 12" stroke = 19-sec cycle (full down and up)
With an 18" stroke = 18 seconds down and 15 seconds up.
A 4" bore ram will be faster.

The pump comes with a 1" suction tail & has a 1/2" BSPT pressure port.
The pump is the highest possible LPM (flow) available for a 10 Hp motor.

The two (2) Stage cast Iron Pump It is a hi-lo design,
this means it pumps High Flow at low Pressures,
this is used when the cylinder is extending or retracting,
but once your forge hits the hot metal of your project to start the deformation process,
it automatically drops to Low Flow High-Pressure cycle
to enable very high pressing forces with good control.

Please note again tonnage is dictated by the bore of your chosen ram.
As an indication, you will produce the following tonnages;
4" bore ram = 16 tonnes
5" bore ram = 25 tonnes.
The larger the bore, the higher the tonnage.

However, the larger bore needs more oil volume, resulting in slower up-down speeds
This is a professional quality unit, made to perform & last
We also stock Australian-made hydraulic rams,

1 spool monoblock valves to operate the up-down function for your press.
Also available are Oil tanks as well as fittings & either swaged-to-length hydraulic hoses
or hose with reusable fittings to allow all hoses to be made by yourself on-site with minimal tools.

Please call us for additional parts or larger / smaller units.
We can supply 5Hp up to 20hp setups. (07) 5563 1982 QLD time
Pick-up is also available from the Gold Coast Qld by appointment ONLY.

19/8/2023 MM SEO, abc, Alt tags.

Save this product for later

All your hydraulic needs in one place! Search products or browse categories below

Products on Hydraulic.Online are described and explained in non technical terms, with photos, charts and or videos. Most of our clients also tend to upgrade to more complete systems this is because they can pick up a phone and call us for a consultation. Call us and experience it for yourself! Australia +61 (07) 5563 1982.

(Hours 8am – 4pm Monday – Friday AEST, excludes National & QLD public holidays)

https://www.youtube.com/watch?v=jpHhaZJd4IE