Phone: (07) 5563 1982 | 1300 146 737

Select Page

Porsche 996 / 997 Turbo Rear Spoiler Wing Hydraulic Lift Cylinders and Pump Overhaul.

996 Turbo Spoiler
AU$1 195.00
In stock
1
Product Details
Brand: Hydraulic.Online

PLEASE NOTE
This Listing is NOT for a new Rear Spoiler Lift and Drop System!

If you have recently seen on your 996 or 997 Porsche Turbo dashboard a red warning light stating

"Failure spoiler control"
or you have noticed the unbalanced or lopsided operation of the Rear Spoiler during lifting and dropping,

or, a wet-looking or Oily hose connection on the bottom of one or both of the Rear Spoiler Hydraulic Actuators,

then your Hydraulic Rear Spoiler system is due for an overhaul.

This price is for you or your mechanic to remove,
carefully pack and send Your Spoiler Cylinders, Pump and Hoses
to us
for a Professional, Thorough and Complete Inspection,
followed by an Overhaul, Reseal, and Pressure Test.

An Optional cylinder removal and installation service is available,
but only at our Gold Coast, QLD, service centre.

We will Professionally Strip and Overhaul the Leaking and or Malfunctioning
Electro Hydraulic Rear Spoiler / Wing Lift and Drop System fitted
to your Porsche 996 or 997 Turbo (2001 to 2012)

Below is a Clip from Porsche enthusiast NeunTwelven's Youtube Video Showing how to disconnect and remove the rear spoiler and
then disconnect and remove the Hydraulic Pump hoses and Actuators from under the rear engine cover.
His video goes on to show how to (in my opinion, temporarily) fix oil leaks by adding a chemical to the hydraulic oil that swells and softens rubber seals. https://youtube.com/clip/Ugkx6SPD7xAvLQTDQWX2lLO-z...

What's included in the price to fully and completely overhaul your Porsche 996 / 997 Turbo Rear Spoiler Lift and Drop System?

  • Strip Down down all components (Including the Two Hydraulic Lift Actuators and the twin-piston Electro-Mechanical Pump)
  • Inspect, clean up and measure all parts.
  • Dismantle, Remanufacture, and Reseal the two main "single acting" Spoiler hydraulic lift cylinders with higher pressure barrels and new long life "nitrile" O rings and seals. (Our Unique Re-Barrel process allows for any future service work to be much more maintenance friendly and economical as well)
  • The Twin Piston Electro-Mechanical Hydraulic Pump is dismantled and all components are checked for excess wear cracks or damage.
  • Pressure testing the new remanufactured barrels and hoses to 70 bar (1,000 psi)
  • Connect all system components and hoses together, bleed the system to remove all trapped air,
    and Pressure Test for correct and even operation so that all you have to do is fit them back
    into your vehicle after we ship them back to you.

Please Note!
Any other additional parts that may be required for example the replacement of
Broken Retract Springs and or a
Pump Bearing block
Electric Motor parts
will be quoted separately.
We do have turning and milling machinery as well as 3D Printing Equipment so most new parts can be manufactured cost-effectively in-house.

Please contact us to determine if this service is suitable for your vehicle.

Email: sales@mhfgc.com.au

Phone Australian Eastern Standard Time
Hours: 8.30 to 4pm Monday - Friday, excluding public holidays
1300 1 HOSES or +61 07 5563 1982

Visits are possible by Appointment Only


Tax invoices are supplied with every purchase

We can also recondition a wide range of other Automotive as well as Industrial cylinders and rams for most vehicles.

Buy with Confidence from a long-established Hydraulic Service Center and get a 12-month warranty and an Australian Tax Invoice.

If you have any questions please don’t hesitate to contact us for further assistance,
Best regards,

Hydraulic.Online


***DISCLAIMER***


IMPROPER SELECTION, INSTALLATION, IMPLEMENTATION, AND/OR OPERATION BY ANYONE OTHER THAN PERSONS WITH APPROPRIATE TECHNICAL AND MECHANICAL TRAINING CAN RESULT IN DAMAGE TO EQUIPMENT OR PROPERTY, SERIOUS PERSONAL INJURY, OR DEATH. PROPER PRECAUTIONS AND SAFETY PROCEDURES SHOULD BE IMPLEMENTED PRIOR TO THE INSTALLATION AND OPERATION OF EQUIPMENT.


MM 26/01/2024 $, abc, added option, Feed

Save this product for later

All your hydraulic needs in one place! Search products or browse categories below

Products on Hydraulic.Online are described and explained in non technical terms, with photos, charts and or videos. Most of our clients also tend to upgrade to more complete systems this is because they can pick up a phone and call us for a consultation. Call us and experience it for yourself! Australia +61 (07) 5563 1982.

(Hours 8am – 4pm Monday – Friday AEST, excludes National & QLD public holidays)

https://www.youtube.com/watch?v=jpHhaZJd4IE