Phone: (07) 5563 1982 | 1300 146 737

Select Page

Tilt Tray Remote Control Hydraulic Valve 5 Lever 3 x Remote. Second Hand 80LPM WALVOIL

AU$2 834.95
Out of stock
Product Details
UPC: Does not apply


This is a great Radio Remote Control System complete with an Italian 5 Spool (5 levers with 3 functions remote controlled) Hydraulic Flow Control Valve rated to 270 bar (3900 psi) and 80 Lt/Min oil flow.

Our brand new system uses an Australian Designed Radio Remote control with a range of up to 150m. It has been tested and found to comply with the limits for a Class [B] digital device, pursuant to the Australian/New Zealand standard AS/NZS 4268.
It is made up with a professionally refurbished SECOND HAND Italian Made WALVOIL Q75-5 Monoblock Hydraulic Flow Control Valve rated for oil flows up to 80 liters per minute at 3900 psi complete with a 8 button hand help radio remote transmitter and a truck-mounted receiver unit. The kit will come as per photos with an Air water separator, air push fittings, airline 12v or 24-volt pneumatic solenoids plus remote & receiver. We provide a fitting diagram so only basic tool & electrical knowledge required for DIY.

For extra ease of wiring, we can supply an wiring harness kit. 6 plug one required for this pack. Please click link. Wiring Harness

This remote control kit will improve the efficiency and speed as well as the safety of your Vehicle Recovery Operations.

The Hydraulic Valve has 5 levers (10 Functions) with Radio Remote Control of 6 functions,
1 & 2 Winch In & Out,
3 & 4 Tray Tilt Up & Down and
5 & 6 Tray Slide In & Out
All 6 functions have manual override, (levers)
Tee Bar Lift & Lower and Slide in & Out are manual lever control only.
Included in the Kit is a SECOND HAND Italian made WALVOIL Q75-5 five spool Hydraulic flow control valve with a rated oil flow of up to 80 Lt/Min and maximum pressure of 3900 PSI.
The hand held 8 Button Radio Remote Transmitter has a range of up to 150 meters. Both the truck mounted Receiver and transmitter are Au/NZ Certified.

Please watch this 2 minute video of us taking a standard 3 spool Hydraulic valve and fitting it with Pneumatic Actuators that will receive the remote signal from the remote control units.

Wired up and connected to 100 PSI of compressed the end result

Designed specifically for Tilt Tray recovery vehicles but can be modified to work on Crane trucks, Skip Bin Trucks, as well as Front End Loaders, Drilling rigs, farming and excavation equipment. Backhoes or any application where you need to control 5 individual cylinders or hydraulic motors (ie winches).
This unit can replace most medium to large tilt tray truck's existing spool valves. Simply bolt on, & either re attach your existing hoses, or if different thread, buy adaptors (we can supply cheaply) to make your existing hose threads compatible.
The remote unit simply needs power, 24 volt DC , & basic wiring to the valve solenoids (wiring diagram provided).
The hydraulic valve will require clean dry compressed air from your truck's air supply for the pneumatic solenoids and spool actuators. Solenoids come complete with push fit air fittings and silencers.
The 8 button remote comes with a transmitter and a receiver. the receiver also has a key pad which can also be used to directly to control the valve.
Levers are still attached for convenient use. This valve comes standard with 5 cylinder spools, which means when the lever/or button are released, the tray, winch etc will lock in place.
These valves are regularly used in hydraulic circuits to divert the flow of high pressure oil and are typically used to control the speed and movement of hydraulic cylinders or motors.
  • Construction = Monoblock
  • Material of Construction = Steel
  • No of Spools = 5
  • No of air/ solenoid actuated spools = 3
  • Air push fits = 4mm
  • Material of Construction = Case Hardened Steel
  • O-rings made of NBR (Buna-N®)
  • Max Flow Rate = 80 liters/min (20 Gallons per Minute)
  • Max Working Pressure = 270 Bar (3900 PSI)
  • Spool Type = Cylinder
  • Spool Movement = Lever action, Spring Return to Center.
  • Built in Relief Valve = Adjustable (factory set at 175 bar 2500 PSI)

Ports Sizes
  • Pressure Port 1/2" BSPP
  • Cylinder Ports 1/2" BSPP
  • Tank Port 3/4" BSPP
  • Power beyond port 3/4" BSPP
  • Operating temperature range: -20 °C to + 80°C
  • Dimensions = L x W x H = 320x 290 x 90 mm (300mm with levers installed)
  • Weight 15 KG
  • Detent Kits also available at $60 each
  • Power beyond plug $23

Need More Information?

Please call Australia +61 07 5563 1982 or send us a an email at

ay for different spool configurations, spool numbers and costings.

Many types of adapters threads, hydraulic hose and field fit hose fittings available please see our other listings

This a High Quality Valve and has many outstanding features, including.
  • built in adjustable relief valve
  • high performance,
  • high efficiency,
  • small volume,
  • mass flow,
  • leak resistance.
  • Compact construction.
  • Low pressure drop.
  • Long service life.
  • High efficiency.
  • Choice of various ports and circuit valves.
  • High accuracy spool is hardened for long term accuracy.
  • Sub-plate mounting.
  • Handle shift operation.

Please note*

These 80 LPM valves require a separate "Power Beyond" sleeve to operate a valve downstream.

Detent is when a you push/pull a lever, it stays forward/back at that position until you move it back to the centre.

Installation ; As per the listed photos, there are a choice of two pressure ports "P" (only use one), two "T" Tank return ports and also there is a "C" port. This "C" port is for the: Power Beyond function. This allows another valve to run pressure from this C port downstream if necessary. (must be a lower volume though). A & B ports run to your cylinder or other functions.


Additional information about us...

Tax invoices are supplied with every purchase

Emails will be answered within normal business hours (ie: 8.30am - 5.00pm M-F)



Save this product for later

All your hydraulic needs in one place! Search products or browse categories below

Products on Hydraulic.Online are described and explained in non technical terms, with photos, charts and or videos. Most of our clients also tend to upgrade to more complete systems this is because they can pick up a phone and call us for a consultation. Call us and experience it for yourself! Australia +61 (07) 5563 1982.

(Hours 8am – 4pm Monday – Friday AEST, excludes National & QLD public holidays)